@@@@@ BEGIN SECTION - inst.id @@@@@
AERI-02
@@@@@ END OF SECTION - inst.id @@@@@
@@@@@ BEGIN SECTION - aerihk.cfg @@@@@
# AERIHK GENERIC   (981201)
# AERIHK is responsible for storing 5-second samples
#  and writes *HK.SPC on request by c&c software


# this is a comment
( this is a comment too )

# set the software release number to be put in all output files
systemreleasenumber 3.0

# scanRate: number of seconds to budget for each pass of
#               the interferometer (see mirror.beg)
scanRate 2.5

# hatchPolarity : 'low' indicates active-low hatch detectors
#                 any other value defaults to active-high
hatchPolarity high

# optionally override max number of stored samples
# generally not used
# numSamples 25

# maxStdDevChannels: name temperature channels on
#    DASHRES card used for maxSampleStdDev calculation
#    generally, this is all the BB thermistors available
maxStdDevChannels ABBapexTemp ABBtopTemp ABBbottomTemp HBBapexTemp HBBtopTemp HBBbottomTemp

# ABBchannels and HBBchannels: name the channels used to calculate *BBmaxTempDiff
#    generally, this is all the available thermistors for a given BB (3 max)
ABBchannels  ABBapexTemp ABBtopTemp ABBbottomTemp
HBBchannels  HBBapexTemp HBBtopTemp HBBbottomTemp
@@@@@ END OF SECTION - aerihk.cfg @@@@@
@@@@@ BEGIN SECTION - mandb @@@@@
2.045739071400253743e-03,3.235582223014191072e+00
2.048078042431634212e-03,4.184914954043023272e+00
2.077557400253590963e-03,2.596049512395939729e+00
2.052665804727994269e-03,3.123734930949712663e+00
2.116144979694382835e-03,2.839650032722776274e+00
2.060555775859815135e-03,2.861068484365713260e+00
2.057414054270225064e-03,3.961910074743185461e+00
2.074655251382212691e-03,3.847890369183778247e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
0.000000000000000000e+00,0.000000000000000000e+00
"""2020-01-24""","""19:33:47.716976"""
# Resistor Set SN02, SCE SN08
# Resistor Set Calibration Date: 1-24-2020@@@@@ END OF SECTION - mandb @@@@@
@@@@@ BEGIN SECTION - rbridge.res @@@@@
10498.5
10499.6
10499.6
10499.6
10499.7
10499.7
10499.7
10499.5
10502.0
10501.8
10501.9
10501.9
10501.9
10502.2
10502.0
10502.4
10500.1
10500.0
10500.1
10500.0
10500.0
10500.1
10500.1
10500.1
10500.8
10500.0
10500.0
10500.0
10500.0
10500.9
10500.9
10500.9
"2005.12.21","12:00:00"
# SCE SN08

@@@@@ END OF SECTION - rbridge.res @@@@@
@@@@@ BEGIN SECTION - numsamps.avg @@@@@
200
"2002.09.01","00:00:00"@@@@@ END OF SECTION - numsamps.avg @@@@@
@@@@@ BEGIN SECTION - abcvals.num @@@@@
0.00101255604, 0.000241946037, 0.000000145278085
0.00101406904, 0.000241761524, 0.000000145224471
0.00101175282, 0.000242046019, 0.000000145145341
0.00101186188, 0.000242133656, 0.000000144366484
0.00101369693, 0.000241915380, 0.000000144288433
0.00101300696, 0.000242029476, 0.000000143750954
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00101227099, 0.000242072098, 0.000000144124903
0.00100950167, 0.000242364407, 0.000000144631945
0.00101099098, 0.000242210346, 0.000000144031189
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
0.00102814693, 0.000239300534, 0.00000015600196
"10-10-2006","19:25:00"
# ABB SN22 -20 - +50  HBB SN16 2015.11.09 NBB SN10
# NBB 6/22/2011
# 66 foot cables@@@@@ END OF SECTION - abcvals.num @@@@@
@@@@@ BEGIN SECTION - motheat.cfg @@@@@
# Motor Preheat config file for AEMIRSAF.
# When AEMIRSAF is run with this config file,
# it will a) grab control of the com port
# b) monitor the mirrorMotorTemp until it reaches operating threshold
# c) send the 1XR10 command to make the mirror go home (ie setup)
# d) release the com port and exit.
#
# When preheating is going on, the "Motor Preheat" session will be present
#   and the mirror motor encoder confirm light will be blue (since the motor
#   is essentially in a safing state).
# RKG 970926

active:=yes
# enable preheating mode on AEMIRSAF
preheating
# the motor should not move when:
mirrorMotorTemp < 233
# delete this one in normal operation -
# rainSensorIntensity > 9000
# run this command on exiting (homing sequence)
command 1XR10

@@@@@ END OF SECTION - motheat.cfg @@@@@
@@@@@ BEGIN SECTION - aeri.pos @@@@@
LAT = 43.070728

LON = -89.406769

ALT = 275.00000

"05-27-2016","21:42:13"


@@@@@ END OF SECTION - aeri.pos @@@@@
@@@@@ BEGIN SECTION - mirror.beg @@@@@
20 1
D5285
HBB 6 60
D-6715
ABB 6 300
D-715
SKY 6 0
D-715
T-SKY 6 0
D-715
U-SKY 6 0
D-715
V-SKY 6 0
D-715
W-SKY 6 0
D-715
X-SKY 6 0
D-715
Y-SKY 6 0
D-715
Z-SKY 6 0
D-6715
ABB 6 300
D5285
HBB 6 60
D-715
SKY 6 0
D-715
T-SKY 6 0
D-715
U-SKY 6 0
D-715
V-SKY 6 0
D-715
W-SKY 6 0
D-715
X-SKY 6 0
D-715
Y-SKY 6 0
D-715
Z-SKY 6 0@@@@@ END OF SECTION - mirror.beg @@@@@
@@@@@ BEGIN SECTION - op.set @@@@@

; Default setup file
;
; General parameters
;
; Instrument type (0=M100 1=MB 2=M120 4=M100 5=MR200)
INSTYP = 1
; Extended (1) or Limited (0) filing system
EXTLIM = 1
; DSP board interrupt number (3 or 5)
DSPINT = 5
; Number of DSP boards installed (1-2)
DSPNUM = 2
; Type of DSP board installed (1=normal DSP 3=1 wait state 4=0 wait state
DSPTYP = 1
; Forward scans only (0) or bidirectional (1)
DIRMOD = 1
; Calibration method = 0 = One point calibration
;                      1 = Two-point calibration with self phase correction
;                      2 = Two-point calib. with black body phase correction
CALIBR = 2
; Combine forward and reverse (1) or not (0) after calibration
COMBIN = 0
; Merge Detector 1 and 2 together (1) or not (0) after calibration
; (valid only with a 2 DSP system )
MERGED = 0
; Cutoff frequency in case of a merge (floating point format)
CUTOFF = 1700.0
; Keep all scans (1) or not (0) (requires LabCalc, output files all become
;                                LabCalc Multifile format)
KEEPSC = 0
; Wavenumber minimum limit for detector #1 (floating point format)
SIGMN1 = 200.0
; Wavenumber maximum limit for detector #1 (floating point format)
SIGMX1 = 2000.0
; Wavenumber minimum limit for detector #2 (floating point format)(optional)
SIGMN2 = 1600.0
; Wavenumber maximum limit for detector #2 (floating point format)(optional)
SIGMX2 = 3020.0
; Apodization function (0=BOXCAR 1=BARTLET 2=COSINE 3=HAMMING 4=BLACKMAN
;			5=GAUSSIAN 6=NORTON_B_WEEK 7=NORTON_B_MEDIUM
; 			8=NORTON_B_STRONG)
; WARNING: DSP96000 only
APODIZ = 0
;
; Cold calibration parameters
;
; Cold calibration Aperture Stop Diameter in cm (floating point format)
CC_ASD = 2.5
; Cold calibration Field Stop Diameter in cm (floating point format)
CC_FSD = 0.64
; Distance or Collimator Focal Length in cm (floating point format)
CC_CFL = 13.9
; Cold Black Body Temperature in Kelvin (floating point format)
CC_BBT = 293.0
; Cold Black Body ambiant temperature in Kelvin (floating point format)
; (optional)
CCAMBT = 300.0
; Cold Black body emissivity (0 <= emissivity <= 1) (floating point format)
; (optional)
CCEMIS = 1.0
; Number of scan to be done for Cold calibration
CCNSCA = 1
; Cold calibration file description
; (must be enclosed in double quotes 80 char. max )
CCDESC = "Sample description for Cold calibration ... "
;
; Hot calibration parameters
;
; Hot calibration Aperture Stop Diameter in cm (floating point format)
HC_ASD = 2.5
; Hot calibration Field Stop Diameter in cm (floating point format)
HC_FSD = 0.64
; Distance or Collimator Focal Length in cm (floating point format)
HC_CFL = 13.9
; Hot Black Body Temperature in Kelvin (floating point format)
HC_BBT = 293.0
; Hot Black Body ambiant temperature in Kelvin (floating point format)
; (optional)
HCAMBT = 300.0
; Hot Black body emissivity (0 <= emissivity <= 1) (floating point format)
; (optional)
HCEMIS = 1.0
; Number of scan to be done for Hot calibration
HCNSCA = 1
; Hot calibration file description
; (must be enclosed in double quotes 80 char. max )
HCDESC = "Sample description for Hot calibration ... "
;
; Sample measurement parameters
;
; Sample measurement Aperture Stop Diameter in cm (floating point format)
SM_ASD = 2.5
; Sample measurement Field Stop Diameter in cm (floating point format)
SM_FSD = 0.64
; Distance or Collimator Focal Length in cm (floating point format)
SM_CFL = 13.9
; Obscuration area (in %)
OBSCAR = 0
; Target area of the Field of view (in %)
TARGAR = 100
; Number of scan to be done for Sample measurement
SMNSCA = 90
; Sample measurement file description
; (must be enclosed in double quotes 80 char. max )
SMDESC = "nothing"

; Instrument parameters
; Laser frequency
LASERF = 15799.7
; Detector of channel #1 (A) preamplifier delay (DSP96000 and MR200 only)
DELAYA = 3.75
; Detector of channel #2 (B) preamplifier delay (DSP96000 and MR200 only)
DELAYB = 3.75

; Instrument settings (DSP96000 and supported instrument only)
; (NOTE: any parameter commented out is not changed)
; Resolution (0=128 1=64 2=32 3=16 4=8 5=4 6=2 7=1 cm-1)
;RESOLU = 5
; Detector #1 gain (1,2,4,8,16)
;GAIND1 = 4
; Detector #2 gain (1,2,4,8,16)
;GAIND2 = 4
; Oversampling for detector #1 (0=1 1=2 sample per fringe)
;OVERS1 = 0
; Oversampling for detector #2 (0=1 1=2 sample per fringe)
;OVERS2 = 0
; Auxiliary detector (0=1st 2=2nd detector)
;AUXDET = 0
DELOS2 = 1.0
@@@@@ END OF SECTION - op.set @@@@@
@@@@@ BEGIN SECTION - aeriemis.asc @@@@@
7/96 Sample #5 (Best of Lot #3 of 2.7 inch Aperture BB's)
400  0.9623
500  0.9628
550  0.9620
600  0.9594
650  0.9560
700  0.9556
740  0.9541
765  0.9548
800  0.9541
850  0.9556
900  0.9560
950  0.9556
1000  0.9503
1060  0.9413
1100  0.9495
1150  0.9686
1200  0.9732
1300  0.9760
1400  0.9766
1510  0.9770
1550  0.9770
1650  0.9770
1700  0.9767
1732  0.9751
1746  0.9744
1800  0.9669
1850  0.9644
1900  0.9636
2030  0.9640
2100  0.9640
2200  0.9646
2300  0.9654
2400  0.9646
2500  0.9646
2600  0.9654
2700  0.9654
2800  0.9661
2900  0.9669
3000  0.9676
3100  0.9676
@@@@@ END OF SECTION - aeriemis.asc @@@@@
@@@@@ BEGIN SECTION - rwaspc.sip @@@@@
(File: RWASPC.SIP -- "static" input parameters for RWASPC)
(GENERIC)
(Note: blank lines, and lines with "(" in col.1, are ignored.)

numberFirstCycle:= 1
numberLastCycle:= 9999
LASERwavenumberCh1:= 15799.30
LASERwavenumberCh2:= 15799.30
@@@@@ END OF SECTION - rwaspc.sip @@@@@
@@@@@ BEGIN SECTION - nlapp.sip @@@@@
(File: NLAPP.SIP -- "static" input parameters for NLAPP)
(AERI-02: 15 Dec. 2015 Test

( modified aperture )

(Note: blank lines, and lines with "(" in col.1, are ignored.)

firstHBBreferenceRecNum(IHREC):= 1
firstInputRecord(IRECLO):= 1
lastInputRecord(IRECHI):= 9999
NLAPPwgt(WGT):= 100000.0
NLAPPeff(EFF):= 0.70
NLAPPfback(FBACK):= 1.0
NLAPPhzpd0(HZPD0):= -74708.3
NLAPPczpd0(CZPD0):= 139042.1
NLAPPnmax(NMAX):= 2
NLAPPan1(AN(1)):= 1.0000000
NLAPPan2(AN(2)):= 6.41E-08
NLAPPan3(AN(3)):= 0.0
NLAPPan4(AN(4)):= 0.0
NLAPPan5(AN(5)):= 0.0@@@@@ END OF SECTION - nlapp.sip @@@@@
@@@@@ BEGIN SECTION - aericalv.sip @@@@@
(File: AERICALV.SIP -- "static" input parameters for AERICALV)
(GENERIC - 970825)

(Note: Comment lines must have a left parenthesis, "(", in the first column,
(      and blank lines are ignored.

hotViewIdentifier(MPHOT):= 'H'
coldViewIdentifier(MPCOLD):= 'A'
firstSceneNumber(NFSCN):= 1
lastSceneNumber(NLSCN):= 9999
outputImaginaryPart(OUTOP2):= 'Y'
outputResponsivity(OUTOP3):= 'Y'
minValidThermistorCount(CTMIN):= -32767
maxValidThermistorCount(CTMAX):=  32767
ratioTestFactor(RATFAC):= 1.5
BBcavityFactor(CAVFAC):= 39.00

(Following 8 parameters are BB Temperature Weights)
ABBtempOffset(ABTOFF):= 0
HBBtempOffset(HBTOFF):= 0
ABBtopTempWeight(WTABBT):= 0.0945
ABBapexTempWeight(WTABBA):= 0.811
ABBbottomTempWeight(WTABBB):= 0.0945
HBBtopTempWeight(WTHBBT):= 0.0945
HBBapexTempWeight(WTHBBA):= 0.811
HBBbottomTempWeight(WTHBBB):= 0.0945@@@@@ END OF SECTION - aericalv.sip @@@@@
@@@@@ BEGIN SECTION - ffovcmr.si1 @@@@@
(File: FFOVCMR.SI1 -- "static" input parameters for FFOVCMR, Ch.1)
(GENERIC  -  981201)

(Note: blank lines, and lines with "(" in col.1, are ignored.)

FFOVhalfAngle(FFOV):= 23
rolloffPointLow(WNL):=520
rolloffPointHigh(WNH):=1800
firstInputRecord(NFR):= 1
lastInputRecord(NLR):= 9999
interferogramLength(NUSED):= 8192
numberOfTerms(NTERMS):= 2
@@@@@ END OF SECTION - ffovcmr.si1 @@@@@
@@@@@ BEGIN SECTION - ffovcmr.si2 @@@@@
(File: FFOVCMR.SI2 -- "static" input parameters for FFOVCMR, Ch.2)
(GENERIC  -  981201)

(Note: blank lines, and lines with "(" in col.1, are ignored.)

FFOVhalfAngle(FFOV):= 23
rolloffPointLow(WNL):=1800
rolloffPointHigh(WNH):=3020
firstInputRecord(NFR):= 1
lastInputRecord(NLR):= 9999
interferogramLength(NUSED):= 8192
numberOfTerms(NTERMS):= 2
@@@@@ END OF SECTION - ffovcmr.si2 @@@@@
@@@@@ BEGIN SECTION - zfli.si1 @@@@@
(File: ZFLI.SI1 -- "static" input parameters for ZFLI, Ch.1)
(GENERIC (981201)

(Note: blank lines, and lines with "(" in col.1, are ignored.)

originalLaserWavenumber(WNLASR):= 15800.1426
firstInputRecord(NFREC):= 1
lastInputRecord(NLREC):= 9999
outputLaserWavenumber(WNLASO):= 15799.0
firstWavenumberOut(WNAO):= 520.0
lastWavenumberOut(WNBO):= 1800.0
FFTpowerOf2(JEXP):= 17
@@@@@ END OF SECTION - zfli.si1 @@@@@
@@@@@ BEGIN SECTION - zfli.si2 @@@@@
(File: ZFLI.SIP -- "static" input parameters for ZFLI, Ch.2)
(GENERIC   - 981201)

(Note: blank lines, and lines with "(" in col.1, are ignored.)

originalLaserWavenumber(WNLASR):= 15800.0651
firstInputRecord(NFREC):= 1
lastInputRecord(NLREC):= 9999
outputLaserWavenumber(WNLASO):= 15799.0
firstWavenumberOut(WNAO):= 1800.0
lastWavenumberOut(WNBO):= 3020.0
FFTpowerOf2(JEXP):= 17
@@@@@ END OF SECTION - zfli.si2 @@@@@
@@@@@ BEGIN SECTION - disk_min.cfg @@@@@
; GENERIC DISK_MIN.CFG (990204)
; Defines minimum disk space to free at the start of a day

DISK_MIN_SPACE = 300000000
@@@@@ END OF SECTION - disk_min.cfg @@@@@
@@@@@ BEGIN SECTION - aerisum.sip @@@@@
(File: AERISUM.SIP -- "static" input parameters for AERISUM)
(GENERIC)

(Note: blank lines, and lines with "(" in col.1, are ignored.)

firstInputRecord(NFR):= 1
lastInputRecord(NLR):= 9999
HBBtempDriftLimit(DHBBMX):= 0.5
LWskyNENlimit(SNENMX(1)):= 1.0
SWskyNENlimit(SNENMX(2)):= 0.05
@@@@@ END OF SECTION - aerisum.sip @@@@@
@@@@@ BEGIN SECTION - channel.map @@@@@
(AERI-Darwin channel.Map of Metrabyte Channels ) (041004)

(Note: Comment lines must have a left parenthesis, "(", in the first column, )
(      and blank lines are ignored.                                          )
( Negative channels represent digitals, of which there are 32 available:     )
(  -1 : first byte, first bit                                                )
(  -9 : second byte, first bit ... etc.                                      )

( History: )
( 961212 : RKG adapted from channel.map and hkchan.txt                       )
( 970707 : fixed up hatchOpenDetect, hatchClosedDetect )
( 970722 : added opticsCompartmentRelativeHumidity )

(Ch.     Short Name in single quotes)

00     'ABBtopTemp'
01     'ABBapexTemp'
02     'ABBbottomTemp'
03     'HBBtopTemp'
04     'HBBapexTemp'
05     'HBBbottomTemp'
06     'fixed2500ohmResistor'
07     'fixed97KohmResistor'
08     'outsideAirTemp'
09     'airNearInterferometerTemp'
10     'interferometerSecondPortTemp'
11     'BBsupportStructureTemp'
12     'airNearBBsTemp'
13     'mirrorMotorTemp'
14     'sceneMirrorTemp'
15     'fixed12KohmResistor'
16     'BBcontroller1temp'
17     'BBcontroller2temp'
18     'coolerCompressorTemp'
19     'coolerExpanderTemp'
20     'coolerPowerSupplyTemp'
21     'rackAmbientTemp'
22     'computerTemp'
23     'motorDriverTemp'
24     'SCEtemp'
25     'coolerCurrent'
26     'detectorTemp'
27     'rainSensorIntensity'
28     'interferometerWindowTemp'
29     'frontEndFanAirUnheatedTemp'
30     'frontEndFanAirHeatedTemp'
31     'spareTemp'
32     'atmosphericRelativeHumidity'
33     'interferometerEnclosureRelativeHumidity'
34     'atmosphericPressure'
35     'sunSensorIntensity'
(1026 'opticsCompartmentRelativeHumidity')

(digitals)
-2 'hatchOpenDetect'
-3 'hatchClosedDetect'
@@@@@ END OF SECTION - channel.map @@@@@
@@@@@ BEGIN SECTION - aerigps.cfg @@@@@
#AERI GPS reception config parameters Darwin (041202)



# AERIGPS communicates with a Motorola Oncore GPS receiver at 9600 bps

# using the Motorola Binary format. It fetches the position/status/time message;

# if sufficient satellites (4) are locked and Dilution of Precision is low enough,

# AERI.POS is generated. If 3 satellite are locked, a GPS time is available.

# It can set the OS/2 system clock to GPS time if permitted below.



# to disable gps, set active:=false/off/no; program will exit without effect

active:=false



# set COM port (RocketPort = COM3 through COM6) GPS receiver is attached to

port:=COM2



# synchronize PC clock to GPS time

time_sync:=off



#Save file "AERI.POS" by not erasing it upon each execution of AERIGPS

SAVE:=False



# optionally force the altitude in AERI.POS, since Z for GPS is rarely useful

#    for fixed land-based operations

locked_altitude:=30 # (in meters)




@@@@@ END OF SECTION - aerigps.cfg @@@@@
@@@@@ BEGIN SECTION - bbctrl.tmp @@@@@
-263.00
-263.00@@@@@ END OF SECTION - bbctrl.tmp @@@@@
@@@@@ BEGIN SECTION - outgoing.lis @@@@@
; COMPREHENSIVE OUTGOING.LIS (981213)
;
; list files to be saved in \OUTGOING as wild card files
;
; Comments begin with ";" or "#"
# Blank lines are ignored

*.par
*.QC
*.sit
*.SUM
*.CSV
*.RNC
*.CXS
*.UVS
*.log@@@@@ END OF SECTION - outgoing.lis @@@@@
@@@@@ BEGIN SECTION - aemirsaf.cfg @@@@@
# AEMIRSAF config file, GENERIC mirror safing config

# default is active, set active:=false to disable safing entirely

# refer to channel.map for sensor names, mirror.beg for

# mirror schedule settings (specifically SCENE view)

active:=true



# one or more conditions stating "safe if" in the form

#       value1 < sensorname < value2

#       value1 > sensorname > value2

#       sensorname < value

#       sensorname > value

-1 < rainSensorIntensity < 9000

#sunSensorIntensity > 1



# optionally override the safing command with a new 'D'

#  mirror controller directive (default is Sky -18000)

# uncomment this line and set mirror value

#D-18650



# the angle to which to safe to, 0 being skyward

# Motor step is computed based on contents of mirror.beg

angle  60



# angle for cleaning the mirror

cleaningAngle 240



# end of AEMIRSAF.CFG
@@@@@ END OF SECTION - aemirsaf.cfg @@@@@
@@@@@ BEGIN SECTION - SUMARY.SCR @@@@@
window with
position of 0 67;
size of 541 141;
real-time is on;
title is "INSTRUMENT ...";
bottom-label is "Time";
decimal-hours-x is on;
visible-menu is off;
horizontal-divisions is 8;
vertical-divisions is 10;
common-x is on;
common-y is on;
graph with
line of red;
range of 0 24 150 350;
FILE(meta:timeHHMMSS:surfaceLayerAirTemp675_680)
end;
graph with
line of blue;
range of 0 24 150 350;
FILE(meta:timeHHMMSS:longwaveWindowAirTemp985_990)
end;
graph with
line of darkgreen;
range of 0 24 150 350;
FILE(meta:timeHHMMSS:shortwaveWindowAirTemp2510_2515)
end;
end;

window with
position of 0 348;
size of 541 141;
real-time is on;
title is "INSTRUMENT ...";
bottom-label is "Time";
decimal-hours-x is on;
visible-menu is off;
horizontal-divisions is 8;
vertical-divisions is 10;
common-x is on;
common-y is off;
graph with
line of black;
range of 0 24 0 1.5;
FILE(meta:timeHHMMSS:coolerCurrent)
end;
graph with
line of red;
range of 0 24 75 80;
FILE(meta:timeHHMMSS:detectorTemp)
end;
end;

window with
position of 0 207;
size of 541 141;
real-time is on;
title is "INSTRUMENT ...";
bottom-label is "Time";
decimal-hours-x is on;
visible-menu is off;
horizontal-divisions is 8;
vertical-divisions is 10;
common-x is on;
common-y is on;
graph with
line of red;
range of 0 24 260 340;
FILE(meta:timeHHMMSS:calibrationHBBtemp)
end;
graph with
line of blue;
range of 0 24 260 340;
FILE(meta:timeHHMMSS:calibrationCBBtemp)
end;
graph with
line of darkgreen;
range of 0 24 260 340;
FILE(meta:timeHHMMSS:BBsupportStructureTemp)
end;
graph with
line of brown;
range of 0 24 260 340;
FILE(meta:timeHHMMSS:calibrationAmbientTemp)
end;
graph with
line of neutral;
range of 0 24 260 340;
FILE(meta:timeHHMMSS:airNearBBsTemp)
end;
graph with
line of yellow;
range of 0 24 260 340;
FILE(meta:timeHHMMSS:interferometerSecondPortTemp)
end;
graph with
line of darkblue;
range of 0 24 260 340;
FILE(meta:timeHHMMSS:spareTemp)
end;
graph with
line of pink;
range of 0 24 260 340;
FILE(meta:timeHHMMSS:outsideAirTemp)
end;
end;
@@@@@ END OF SECTION - SUMARY.SCR @@@@@
@@@@@ BEGIN SECTION - AESITTER.SCR @@@@@
# Darwin instrument - (041203)
#
#  Limits Tests for AERI:  AESITTER input script
#
#  R. Dedecker / R. Garcia
#  Space Science and Engineering Center
#  University of Wisconsin-Madison
#  updated 2/3/03 J. Demirgian
#
# invocation : aesitter -DFILE=test.sum -x=100 -y=100 test.scr
# position for AERI windows  position is 375 100;
position is 539 84;
help file is aesitter.hlp;
title is INSTRUMENT ...;
metadata FILE is
date is
position is 1 1;
meaning is "instrument date";
prefix is "Date ";
format is yymmdd;
dateYYMMDD
end;

time is
position is 2 1;
meaning is "instrument time";
help id is 50025;
prefix is "UTC ";
format is hhmmss;
timeHHMMSS
end;

record is
position is 3 1;
meaning is "record number";
help id is 50020;
prefix is "Record ";
0
end;

Latitude is
position is 1 2;
meaning is "GPS latitude";
prefix is "Lat ";
format is time;
Latitude
end;

Longitude is
position is 2 2;
meaning is "GPS longitude";
prefix is "Lon ";
format is time;
Longitude
end;

Mirror Angle is
position is 3 2;
meaning is "Mirror Angle";
prefix is "Scene Mirror Angle ";
format is integer;
sceneMirrorAngle
end;

ABB Temp is
position is 1 3;
yellow is 243.15 313.15;
green is 248.15 308.15;
calibrationCBBtemp
end;

Outside Air Temp is
position is 2 3;
yellow is 233.15 323.15;
green is 253.15 313.15;
help id is PrimaryPanel;
outsideAirTemp
end;

Rack Ambient Temp is
position is 3 3;
yellow is 277.15 319.15;
green is 282.15 314.15;
rackAmbientTemp
end;

Rain Intensity is
position is 3 10;
yellow is 6000 11000;
green is 9400 10000;
rainSensorIntensity
end;

ABB Max Temp Diff is
position is 1 4;
green is  0 0.05;
yellow is 0 0.1;
ABBmaxTempDiff
end;

BB Support Struct. Temp is
position is 2 4;
yellow is 233.15 323.15;
green is 253.15 313.15;
BBsupportStructureTemp
end;

Computer  Temp is
position is 3 4;
yellow is 277.15 319.15;
green is 282.15 314.15;
computerTemp
end;

Hatch Open is
position is 3 16;
yellow is 0 0;
green is 1 2;
hatchOpen
end;

HBB Temp is
position is 1 5;
yellow is 263.15 353.15;
green is 332.5 333.5;
calibrationHBBtemp
end;

Air Temp Near BBs is
position is 2 5;
yellow is 233.15 343.15;
green is 253.15 338.15;
airNearBBsTemp
end;

SCE Temp is
position is 3 5;
yellow is 273.15 333.15;
green is 278.15 328.15;
SCEtemp
end;

HBB Max Temp Diff is
position is 1 6;
green is  0 0.4;
yellow is 0 0.7;
HBBmaxTempDiff
end;

Scene Mirror Temp is
position is 3 12;
yellow is 233.15 343.15;
green is 253.15 338.15;
sceneMirrorTemp
end;

ABB  Controller Temp is
position is 3 6;
yellow is 273.15 323.15;
green is 278.15 318.15;
BBcontroller1temp
end;

Air Humidity is
position is 2 6;
yellow is 1.0 99.0;
green is 10.0 97.0;
atmosphericRelativeHumidity
end;

HBB Temp Stability is
position is 1 7;
yellow is -0.5 0.5;
green is -0.05 0.05;
HBBtempDrift
end;

Mirror Motor Temp is
position is 2 7;
yellow is 233.15 363.15;
green is 238.15 333.15;
mirrorMotorTemp
end;

HBB  Controller Temp is
position is 3 7;
yellow is 273.15 323.15;
green is 278.15 318.15;
BBcontroller2temp
end;

Atmos. Pressure is
position is 2 8;
yellow is 900.0 1040.0;
green is 920.0 1025.0;
atmosphericPressure
end;

336 Kelvin (Reference) is
position is 1 8;
yellow is 336.064 336.184;
green is 336.094 336.154;
help id is 50060;
fixed2500ohmResistor
end;

Air Flow Delta Temp is
#               position is 2 8;
position is 3 13;
#                yellow is .50 3.2;
#                green is .65 2.8;
yellow is -3.2 3.2;
green is -2.8 2.8;

frontEndFanAirTempDiff
end;

Cooler Pwr Sup. Temp is
position is 3 8;
yellow is 281.15 333.15;
green is 288.15 328.15;
coolerPowerSupplyTemp
end;

293 Kelvin (Reference) is
position is 1 9;
yellow is 293.612 293.732;
green is 293.642 293.702;
help id is 50055;
fixed12KohmResistor
end;

Spare Temp is
position is 2 9;
yellow is 281.15 308.15;
green is 288.15 303.15;
help id is PrimaryPanel;
spareTemp
end;

Motor Driver Temp is
position is 3 9;
yellow is 273.15 323.15;
green is 278.15 318.15;
motorDriverTemp
end;

#       Sun Intensity is
#               position is 4 9;
#               yellow is 273.15 323.15;
#               green is 278.15 318.15;
#        sunSensorIntensity
#       end;

249 Kelvin (Reference) is
position is 1 10;
yellow is 249.192 249.312;
green is 249.222 249.282;
help id is 50055;
fixed97KohmResistor
end;

Interfer. Window Temp is
position is 2 10;
yellow is 281.15 323.15;
green is 293.15 309.15;
interferometerWindowTemp
end;

Max Sample StdDev is
position is 1 11;
green is 0 0.137;
yellow is 0 0.177;
maxSampleStdDev
end;

Interfer. 2nd Port Temp is
position is 2 11;
yellow is 288.15 313.15;
green is 293.15 308.15;
interferometerSecondPortTemp
end;

Encoder Scene Confirm is
position is 3 11;
yellow is -5 5;
green is -2.5 2.5;
sceneMirPosEncoderDrift
end;

#       Maximum Roll is
# AERI window position          position is 4 11;
#               position is 3 12;
#               yellow is -15 15;
#               green is -5 5;
#         maxRoll
#       end;

LW HBB NEN is
position is 1 12;
green is 0 0.2;
yellow is 0 1;
LW_HBB_NEN
end;

Air Temp Near Interfer. is
position is 2 12;
yellow is 281.15 308.15;
green is 288.15 303.15;
airNearInterferometerTemp
end;

#       Maximum Pitch is
# AERI window position          position is 4 12;
#               position is 3 13;
#               yellow is -15 15;
#               green is -5 5;
#         maxPitch
#       end;

SW HBB NEN is
position is 1 13;
green is 0 0.015;
yellow is 0 0.1;
SW_HBB_NEN
end;

Interfer. Humidity is
position is 2 13;
yellow is 12.0 20.0;
green is 0.0 12.0;
interferometerEnclosureRelativeHumidity
end;

LW Responsivity is
position is 1 14;
green is 0.43 2.0;
yellow is 0.40 2.0;
LWresponsivity
end;

Cooler Comp. Temp is
position is 2 14;
yellow is 281.0 313.0;
green is 288.0 308.0;
coolerCompressorTemp
end;

Cooler Current is
position is 3 14;
yellow is 0.2 1.2;
green is 0.3 1.15;
coolerCurrent
end;

SW Responsivity is
position is 1 15;
green is 8.5 15.0;
yellow is 8.06 15.0;
SWresponsivity
end;

Cooler Expander Temp is
position is 2 15;
yellow is 281. 313.;
green is 288. 310.;
help id is 50075;
coolerExpanderTemp
end;

Detector Temp is
position is 3 15;
yellow is 74.0 85.0;
green is 75.0 79.0;
detectorTemp
end;

#        Optics Humidity is
#                position is 2 16;
#                yellow is 12.0 20.0;
#                green is 0.0 12.0;
#          opticsCompartmentRelativeHumidity
#        end;
end;@@@@@ END OF SECTION - AESITTER.SCR @@@@@
@@@@@ BEGIN SECTION - RADIANCE.SCR @@@@@
window with
position of 0 485;
size of 509 285;
real-time is on;
title is "INSTRUMENT Ch. 1 Rad. [...]";
bottom-label is "Wavenumber";
common-x is on;
common-y is off;
graph with
line of black;
range of 500 1500 0 180;
FILE1(1data1:1)
end;
end;

window with
position of 506 486;
size of 518 285;
real-time is on;
title is "INSTRUMENT Ch. 2 Rad. [...]";
bottom-label is "Wavenumber";
common-x is on;
common-y is off;
graph with
line of black;
range of 2000 3000 0 10;
FILE2(1data1:1)
end;
end;
@@@@@ END OF SECTION - RADIANCE.SCR @@@@@